Recent Comments

How to Make a Fast Pinewood Derby Car

SAFETY FIRST: Ask an adult to help with tools you haven't used before.

derby-featured

Packs around the country are preparing to hold their annual Pinewood Derby. There are many ways to make your Pinewood Derby car go faster. Here are some of them.

Basic Guidelines for Pinewood Derby Car Design

The possibilities are endless when it comes to picking a shape for your Pinewood Derby car. Before you begin, consider the following general guidelines:

Avoid designs with a pointed nose. A pointed nose will make it difficult for your Pinewood Derby car to rest on the pin at the starting gate. It may also cause your Pinewood Derby car to get bumped around when the pin drops, and it can create problems for electronic timing systems.

Leave enough wood in the rear of the Pinewood Derby car so you can place additional weight there. You will end up placing most of the weight in the rear of the Pinewood Derby car.

Make the maximum weight. Your car should weigh as much as it’s allowed. In most races, a Pinewood Derby car’s weight is limited to 5 ounces. If your car weighs less than that, add coins or other weights.

Be sure that it is very clear which end of your Pinewood Derby car is the front and which end is the back. In many races, the race officials —- not you -— will actually place each Pinewood Derby car on the track. Sometimes the officials put the Pinewood Derby car on the track backward because they can’t tell which end is which.

Choose a design that allows the air to move over and around the Pinewood Derby car body in a smooth manner. Pinewood Derby cars with aerodynamic profiles go faster.

Click here to see photo galleries of hundreds of Pinewood Derby car designs.


pinespeed2

Designing and Building a Winning Pinewood Derby Car

You don’t have to strive for the fastest Pinewood Derby car to have fun competing in your Pinewood Derby. But if you and a helpful adult are willing to put in the extra time and effort, these tips are for you.

1. Bake the Block: Start with your block of wood, and before you do anything else, bake it in the oven at 250 degrees for around two hours to remove moisture and make it lighter. This will allow you to place more weight to the rear of the Pinewood Derby car where you actually want it.

pinewood-aero

2. Create the Design: Draw the outline of your Pinewood Derby car on a sheet of paper, cut it out and attach it to your block of wood.

Remember, a rectangular car is not an aerodynamic design. The most basic aerodynamic design is a simple wedge. If you don’t have time to design a complex car, a wedge will work just fine.

Click here to download a Pinewood Derby car template PDF to help you create your design.

3. Rough Cut the Design: Use a coping saw to cut out the rough shape of your Pinewood Derby car. You can also ask a responsible adult to make these cuts using a power tool.

4. Shape Your Car: Use sand paper to smooth your car’s edges and shape it to your design. An adult can also use a rotary tool or other tool to help you.

5. Sand and Paint the Pinewood Derby Car: Make it smooth to reduce friction and paint an awesome design to make it look great.

Click here for tips on painting your Pinewood Derby car to give it a shiny finish.

6. Install Axles and Wheels: Make sure they are aligned perfectly straight. You can test the alignment of your axles by pushing your car across a smooth floor or table. It should roll smoothly in a straight line.

— Make a Three-Wheeler: Raise one wheel about 1/16 inch higher so it never actually touches the track. Less friction = more speed. Rules vary from pack to pack, so make sure to check your pack’s Pinewood Derby rules to make sure three wheelers are allowed in your race.

— Extend the Wheelbase: The front and rear wheels should be as far apart as possible. Again, make sure this is allowed in your race.

Click here to learn about polishing Pinewood Derby axles and wheels to reduce friction.

7. Create Glue Holes: Glue the axles firmly in their holes to ensure that they stay perfectly placed, but make sure you don’t get glue on your wheels.

8. Add Weight: Remember to make your Pinewood Derby car as heavy as the rules allow. In general, it’s best to place weight to the rear of your car because a heavier rear increases speed.

Click here for scientific Pinewood Derby speed tips from a former NASA engineer

9. Lubricate the Wheel Well: Add graphite or another dry lubricant to reduce friction. The less friction between the body and wheel, the better.

And finally, remember the No. 1 rule of a Pinewood Derby is that it’s supposed to be fun. While you should always strive to do your best, don’t get caught up in winning or having the fastest car. Just enjoy the ride.

Adapted from the book “Pinewood Derby Speed Secrets,” DK Publishing, $12.95 softcover.


Submit a Photo of Your Project

Important Note: Please only upload photos of your project. Because of privacy rules, we can't post any photos that show people's faces. Always ask for your parent's permission before uploading anything to a website.

15 Comments on How to Make a Fast Pinewood Derby Car

  1. Very cool and fun pinewood derby

  2. this is raele gate to halp me win

  3. This artiucle helped me and my not so helpful team win a school science contest. Thank you !!!!!!!~!!!!!!! Sincerely, Person from New Jersey.

  4. I think your article was informational and really helps people when it comes to build a car.

  5. The soon-to-be Tenderfoot // January 5, 2022 at 8:59 am // Reply

    So sad I can’t compete this year!

  6. Eevee POKEMON // February 22, 2021 at 2:21 pm // Reply

    download pokemon and animal crossing

  7. Most IMPORTANT, HAVE FUN!!

  8. These tips are great but in most cases entries must have all four wheels touching the track. There are also some restrictions on how wide the wheel base can be so make sure you know the rules of the race before you make alterations.

  9. Thanks!

  10. Great tips guys!

  11. 1stOnRaceDay // January 14, 2020 at 6:27 am // Reply

    Pinewood derby is a great way to teach cubs about physics. Basically the car body represents stored energy. One trick to speeding up a car is to remove mass from the wheels so that less energy is required to start and keep the wheels turning. Less mass in the wheels also allows more weight to be added to the body.

  12. Doing good guys doing good

  13. cool
    awesome
    fun

  14. Also make sure that you also smooth down any plastic burs on the wheels but make sure you do not create any flat spots while doing so.

Leave a Reply to tuttifrutti Cancel reply

Please don't use your real name.